43-1130.fm Page 1 Tuesday, May 30, 2000 1:22 PM
TAD 1130
2.4 GHz Digital Spread Spectrum
Cordless Speakerphone
with Digital Answering System
43-1130.fm Page 3 Tuesday, May 30, 2000 1:22 PM
Adjusting the TAD’S Volume ........................................................................................... 19
Deleting Messages ......................................................................................................... 19
Setting the Remote Operation Pin .................................................................................. 19
Remote Operation .......................................................................................................... 20
Using the Toll-Saver ....................................................................................................... 20
Using Remote Commands ............................................................................................. 20
Remote Commands ................................................................................................ 21
Troubleshooting ................................................................................................................... 22
Care ................................................................................................................................ 23
WARNING:
shock hazard, do not expose this product to rain
or moisture.
To reduce the risk of fire or
IMPORTANT SAFETY
INSTRUCTIONS
When using your telephone equipment, ba-
sic safety precautions should always be fol-
lowed to reduce the risk of fire, electric shock
and injury to persons, including the following:
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF
1. Read and understand all instructions.
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
2. Follow all warnings and instructions
marked on the product.
3. Never install telephone wiring during a
lightning storm.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con-
stitute a risk of electric shock. Do
not open the product’s case.
4. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
5. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the net-
work interface.
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accom-
panying this product.
!
6. Use caution when installing or modifying
telephone lines.
7. Do not affix the AC power supply cord to
building surfaces with metal fittings (if
the product has an AC power cord).
This phone has been tested and found to
comply with all applicable UL and FCC stan-
dards.
8. Unplug this product from the wall outlet
before cleaning. Do not use liquid clean-
ers or aerosol cleaners. Use a damp
cloth for cleaning.
3
43-1130.fm Page 4 Tuesday, May 30, 2000 1:22 PM
9. Do not use this product near water, for
example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
repair work is required. Opening or
removing covers may expose you to
dangerous voltages or other risks. Incor-
rect reassembly can cause electric
shock when the product is subsequently
used.
10. Do not place this product on an unstable
cart, stand, or table. The product may
fall, causing serious damage to the
product.
17. Unplug this product from the wall outlet
and refer servicing to qualified services
personnel under the following condi-
tions:
11. Slots and openings in the telephone’s
cabinet and the back or bottom are pro-
vided for ventilation. To protect the tele-
phone from overheating, these openings
must not be blocked or covered. The
openings should never be blocked by
placing the product on a bed, sofa, rug,
or other similar surface. This product
should never be placed near or over a
radiator or heat register. This product
should not be placed in a built-in instal-
lation unless proper ventilation is pro-
vided.
• When the power cord plug is damaged
or frayed.
• If liquid has been spilled into the prod-
uct.
• If the product has been exposed to rain
or water.
• If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are cov-
ered by the operating instructions
because improper adjustments of other
controls may result in damage and will
often require extensive work by a quali-
fied technician to restore the product to
normal operation.
12. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the type of power supply to your
home, consult your local power com-
pany.
• If the product has been dropped or the
cabinet has been damaged.
13. Do not allow anything to rest on the
power cord. Do not locate this product
where the cord will be stepped on.
• If the product exhibits a distinct change
in performance.
14. Do not overload wall outlets and exten-
sion cords as this can result in a risk of
fire or electric shock.
18. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
15. Never push objects of any kind into this
product through cabinet slots as they
may touch dangerous voltage points or
short out parts that could result in a risk
of fire or electric shock. Never spill liquid
of any kind on the product.
19. Do not use the telephone to report a gas
leak while in the vicinity of the leak.
16. To reduce the risk of electric shock, do
not disassemble this product. Take it to
a qualified serviceman when service or
4
43-1130.fm Page 5 Tuesday, May 30, 2000 1:22 PM
draw as the phone’s ringer equivalence num-
ber, or REN. The REN is on the bottom of
your phone.
BATTERY SAFETY
INSTRUCTIONS
CAUTION:
TO REDUCE THE RISK OF
If you use more than one phone or other de-
vice on the line, add up all the RENs. If the
total is more than five (three in rural areas),
your phones might not ring. If ringer opera-
tion is impaired, remove one of the devices
from the line.
FIRE OR INJURY, READ AND FOLLOW
THESE INSTRUCTIONS.
1. Use only the appropriate type and size
battery pack specified in the instruction
manual provided for this product.
Important:
2. Do not dispose of the battery pack in a
fire. The cell may explode. Check with
local codes for possible special disposal
instructions.
• Cordless phones such as this one
require AC power to operate. When the
AC power is off, you cannot dial out or
receive incoming calls using your
phone. To be safe, you should also have
a phone that does not need AC power to
operate (not a cordless phone) so you
can still make and receive calls if there
is an AC power failure.
3. Do not open or mutilate the battery
pack. Released electrolyte is corrosive
and may cause damage to the eyes or
skin. It may be toxic if swallowed.
4. Exercise care in handing the battery
pack in order not to short it with conduct-
ing materials such as rings, bracelets
and keys. The battery or conductor may
overheat and cause burns.
• When AC power is lost, the phone loses
the security access-protection code con-
nection between the base and the hand-
set. When power is restored, put the
handset on the base briefly to restore
this connection.
5. Charge the battery pack provided with or
identified for use with this product only in
accordance with the instructions and
limitations specified in the instruction
manual provided for this product.
FCC STATEMENT
Your telephone complies with Part 68 of FCC
Rules. Upon request, you must provide the
phone’s FCC registration number and REN
to your telephone company. These numbers
are on the bottom of the base.
6. Observe proper polarity orientation
between the battery pack and battery
charger.
SAVE THESE
INSTRUCTIONS
Note:
to:
You must not connect your telephone
READ THIS BEFORE
INSTALLATION
• coin-operated systems
• party-line systems
We have designed your phone to conform to
federal regulations and you can connect it to
most phone lines. However, each device that
you connect to the telephone line draws
power from the line. We refer to this power
• most electronic key phone systems
5
43-1130.fm Page 6 Tuesday, May 30, 2000 1:22 PM
• connecting your phone to an AC outlet
that is on a different electrical circuit
from the receiver contacting your local
RadioShack store for help
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone causes
problems on the phone line, the phone com-
pany can temporarily discontinue your ser-
vice. If this happens, the phone company
attempts to notify you in advance. If advance
notice is not practical, the phone company
notifies you as soon as possible and advises
you of your right to file a complaint with the
FCC.
If you cannot eliminate the interference, the
FCC requires that you stop using your
phone.
Some cordless telephones operate on fre-
quencies that might cause interference to
nearby TVs and VCRs. To minimize
or prevent such interference, the base of the
cordless telephone should not be placed
near or on top of a TV or VCR.
Also, the phone company can make changes
to its lines, equipment, operations, or proce-
dures that could affect the operation of this
telephone. The telephone company notifies
you of these changes in advance, so you can
take the necessary steps to prevent interrup-
tion of your telephone service.
LIGHTNING
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line and power line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.
Your phone might cause TV or radio interfer-
ence even when it is operating properly. To
determine whether your phone is causing the
interference, turn off your phone. If the inter-
ference goes away, your phone is causing it.
Lightning damage is not common. Neverthe-
less, if you live in an area that has severe
electrical storms, we suggest that you unplug
your phone when storms approach to reduce
the possibility of damage.
Try to eliminate the interference by:
• moving your phone away from the
receiver
ˆ Features
Your RadioShack 2.4 GHz Cordless Speak-
erphone combines a 2.4 GHz digital cordless
telephone unit and a digital TAD (Telephone
Answering Device). The 2.4 GHz band
means less interference, clearer sound, and
greater range than other types of cordless
telephones.
• You can delete individual messages and
save the rest.
• There are no tapes to bother with and no
tape mechanisms to wear out.
The remote operation feature lets you oper-
ate your TAD from a touch-tone phone (or
from a rotary phone with an optional pocket
tone dialer).
The TAD stores up to 18 minutes of messag-
es on a computer chip and records each
message’s day and time. This gives you ad-
vanced capabilities over tape-based answer-
ing machines:
6
Features
43-1130.fm Page 7 Tuesday, May 30, 2000 1:22 PM
TELEPHONE FEATURES
ANSWERING SYSTEM
FEATURES
10 Number Memory Dialing
— lets you
store 10 numbers in memory for easy dialing.
Day/Time Stamp
— records the day and
time each message was recorded.
Page
— lets you send a paging signal from
the base to the handset to page someone or
locate the handset if you misplace it.
Two Prerecorded Messages
the option of using one of two prerecorded
outgoing messages or recording your own.
— gives you
30 Channels
— automatically selects a clear
channel when you make or answer a call.
You can also manually change channels dur-
ing a call.
Announcement Only
nouncement for callers to hear, without re-
cording their messages.
— lets you play an an-
Security Access-Protection Code
prevent other cordless phone users from us-
ing your phone line.
— helps
Message Counter
messages the TAD has recorded.
— shows the number of
Programmable PIN
digit personal identification number (PIN) for
secure remote operation.
— you can set a two-
Ringer Volume Control
from four ringer tone/volume settings on the
handset.
— lets you select
Call Screening
leaves a message so you can decide wheth-
er or not to answer the call.
— lets you listen as a caller
Volume Controls
ume you hear through the handset.
— let you adjust the vol-
Long Battery Life
— the supplied battery
Memo Recording
— lets you leave messag-
pack (when fully charged) provides about 6
hours of talk time or 7 days of standby time.
es for yourself or others in your home or of-
fice. You can also record your phone
conversation.
Tone/Pulse Dialing
— lets you use either
type of service, and you can easily switch
from pulse to tone dialing for long-distance,
bank-by-phone, or other special services.
Room Monitor
mote phone to the room where the TAD is in-
stalled.
— lets you listen from a re-
Auto Talk
by lifting the handset from the base.
— lets you answer a call simply
Phone Pick-Up Detection
— stops record-
ing when you pick up any phone on the same
line as the TAD, and resets to answer the
next call.
Any Key Answer
to answer a call when the handset is away
from the base.
— lets you press any key
Adjustable Ring Number
— lets you set the
TAD to answer after three or five rings.
Hearing-Aid Compatibility
— lets you use
your phone with hearing aids that have a T
(telephone) switch.
Toll-Saver
— lets you avoid unnecessary
charges when you call by long distance to
check your messages.
Digital Volume Control
— lets you precisely
adjust the speakerphone and message play-
back volume.
7
Features
43-1130.fm Page 8 Tuesday, May 30, 2000 1:22 PM
ˆ Installation
Notes:
• Your telephone connects directly to a
MOUNTING THE PHONE
You can place the TAD’s base on a desk or
table, or mount it on a standard wall plate or
directly on a wall.
modular telephone line jack. If your
phone line jack is not a modular jack,
you can update the wiring yourself,
using jacks and adapters available at
your local RadioShack store. Or, you
can let the phone company update the
wiring for you.
Choose a location that is:
• near an AC outlet
• near a modular telephone line jack
• out of the way of normal activities
• The USOC number of the jack to be
installed is RJ11C (RJ11W for a wall
plate).
• away from electrical machinery, electri-
cal appliances, metal walls or filing cabi-
nets, wireless intercoms, alarms, and
room monitors
On a Desk Top
1. Insert the bracket’s tabs into the base’s
upper tab slots, then press down on the
bracket’s clips and insert them into the
clip slots.
• away from other cordless phones
The base’s location affects the phone’s
range. If you have a choice of several loca-
tions, try each to see which provides the best
performance.
2. Plug one end of the supplied long modu-
TEL LINE
lar cord into the
back of the base.
jack on the
Cautions:
3. Plug the modular cord’s other end into a
modular telephone line jack.
You must use a Class 2 power
source that supplies 9V DC
!
4. Insert the supplied AC adapter’s barrel
and delivers at least 350 mA.
Its center tip must be set to positive and
DC IN 9V
plug into the
the base.
jack on the back of
DC IN 9V
its plug must fit the telephone's
jack. The supplied adapter meets these
specifications. Using an adapter that
does not meet these specifications
could damage the telephone or the
adapter.
5. Route the adapter’s cord through the
strain relief slot on the bracket.
• Always connect the AC adapter to the
phone before you connect it to AC
power. If you disconnect the power, dis-
connect the adapter from AC power
before you disconnect it from the phone.
6. Plug the adapter into a standard AC out-
let.
8
Installation
43-1130.fm Page 9 Tuesday, May 30, 2000 1:22 PM
7. Lift the base’s antenna to a vertical posi-
tion.
7. Press and lift out the handset holder, flip
it over, then snap it back into place so it
holds the handset.
On a Wall Plate or Wall
1. Insert the bracket’s tabs into the base’s
lower tab slots, then press down on the
bracket’s clips and insert them into the
clip slots.
8. Lift the base’s antenna to a vertical posi-
tion.
2. Plug one end of the supplied short mod-
TEL LINE
ular cord into the
back of the base.
jack on the
Note:
To mount the TAD directly on a wall,
you need two screws (not supplied) with
heads that fit into the keyhole slots on the
bottom of the base.
3. Insert the supplied AC adapter’s barrel
DC IN 9V
plug into the
the base.
jack on the back of
Follow the steps under “On a Wall Plate or
Wall,” then apply these additional instruc-
tions for placement on a wall.
4. Route the adapter and modular cords
through the grooves on the bracket.
1. Drill two holes 315/16
5
/16"
inches (100 mm) apart.
Then thread a screw into
each hole, letting the
15
heads extend about 5/16
3 /16"
inch (8 mm) from the wall.
5. Plug the modular cord’s other end into
the wall plate jack, then align the
bracket’s keyhole slots with the wall
plate studs and slide the base down-
ward to secure it.
2. Plug one end of the sup-
plied long modular cord
TEL LINE
into the
base.
jack at the back of the
3. Align the bracket’s keyhole slots with the
mounting screws and slide the base
downward to secure it.
6. Plug the adapter into a standard AC out-
let.
9
Installation
43-1130.fm Page 10 Tuesday, May 30, 2000 1:22 PM
Notes:
• When you first use the phone after
CONNECTING, CHARGING,
AND REPLACING THE
BATTERY PACK
charging or recharging the battery pack,
the phone might not work and you might
hear a five-beep error signal. If this hap-
pens, return the handset to the base for
about 5 seconds to reset the security
access-protection code.
The TAD comes with a rechargeable nickel-
cadmium battery pack installed in the hand-
set, but not connected. Before using your
phone, you must connect the battery pack,
then charge it for about 24 hours.
• Using a pencil eraser, clean the charg-
ing contacts on the handset and the
base about once a month.
1. Press down and slide off the battery
pack compartment cover.
• If the phone does not work, recharge the
battery pack. (The battery power might
be too low to flash the TALK/LOW BATT
indicator.)
• If the battery pack becomes weak during
a call, the handset beeps every 3 sec-
onds. When this happens, you cannot
make a call on the phone until you
recharge the battery pack.
2. Lift the battery pack out of the compart-
ment. Plug the battery pack’s connector
into the socket in the compartment. The
connector fits only one way.
• About once a month, fully discharge the
battery pack by keeping the handset off
the base until the TALK/BATT LOW indi-
cator flashes. Otherwise, the battery
pack loses its ability to fully recharge.
• If the battery pack is completely dis-
charged or the base loses power while
the handset is away from it, place the
handset on the base to reset the secu-
rity access-protection code. If it was the
handset that lost power, recharge the
battery pack.
3. Put the battery pack in the compartment.
4. Replace the cover.
To charge the battery pack, simply place the
handset on the base, facing either up or
down. The CHARGE/IN USE indicator on the
base lights.
The supplied battery pack should last about
a year. If the battery pack does not hold a
charge for more than 2 hours after an over-
night charge, replace it with a new 3.6-volt,
600 mAh battery pack with a connector that
fits the socket in the battery compartment.
You can order a replacement battery pack
through your local RadioShack store. Install
the new battery pack and charge it for about
24 hours.
Recharge the battery pack when the TALK/
LOW BATT indicator flashes.
Important:
Be sure the battery pack is prop-
erly connected before you try to charge it. If
the CHARGE/IN USE indicator flashes slow-
ly when the handset is on the base, the bat-
tery pack is not connected properly.
10
Installation
43-1130.fm Page 11 Tuesday, May 30, 2000 1:22 PM
Warning:
Dispose of the old battery pack
promptly and properly. Do not burn or bury it
(see “Battery Safety Instructions” on Page 5
for additional information on proper battery
handling).
If you have trouble replacing the battery
pack, take the phone to your local Ra-
dioShack for assistance.
Important:
The EPA certified
RBRC® Battery Recycling Seal
on the nickel-cadmium (Ni-Cd)
battery indicates RadioShack
is voluntarily participating in an
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a con-
venient alternative to placing used Ni-Cd bat-
teries into the trash or the municipal waste
stream, which may be illegal in your area.
Please call 1-800-THE-SHACK (1-800-843-
7422) for information on Ni-Cd battery recy-
cling and disposal bans/restrictions in your
area. RadioShack’s involvement in this pro-
gram is part of the company’s commitment to
preserving our environment and conserving
our natural resources.
11
Installation
43-1130.fm Page 12 Tuesday, May 30, 2000 1:22 PM
A QUICK LOOK AT THE HANDSET
Note:
The handset window has plastic film on it to protect it during shipment. Carefully peel off
the film before using your phone for the first time.
Use VOL
/
to adjust
8 9
the handset volume (see
“Adjusting the Handset
Volume” on Page 14).
Use MUTE talk to some in the
room without the person on the
other end of the phone line
hearing your conversation (see
“Using Mute” on Page 15
Use MEMORY to store and dial
names and numbers in memory
(see “Memory Dialing” on
Page 15).
Use FLASH to select the
phone’s flash function
(see “Using Flash” on
Page 15).
Use TALK to make a
call (see “Making
and Receiving Calls
with the Handset”
on Page 14).
Use CHANNEL to select the
phone’s channels (see “Se-
lecting the Channel” on
Use REDIAL to redial
the last number dialed
(see “Using Redial” on
Page 15).
Page 14) and other options.
Use PAUSE to store a pause
in a number (see “Entering a
Pause” on Page 16).
Press TONE to use your phone
company’s special tone services
when you are on a pulse line (see
“Using Tone Services on a Pulse
Line” on Page 15).
Note:
If your phone system requires that
SETTING THE DIALING
MODE
you dial an access code (9, for example)
before you dial an outside number, do
not press the access code number
either.
PULSE-TONE
Set
on the back of the base for
the type of service you have. If you are not
sure which type you have, after you charge
the handset battery pack, do this simple test.
If the dial tone stops, you have touch-
tone service. Leave
PULSE-TONE
set to
TONE
.
PULSE-TONE
TONE
.
1. Set
to
If the dial tone continues, you have
TALK
2. Lift the handset, press
for a dial tone.
and listen
PULSE-TONE
pulse service. Set
to
PULSE
.
3. Press any number other than 0.
12
Installation
43-1130.fm Page 13 Tuesday, May 30, 2000 1:22 PM
TALK
4. Press
or place the handset on the
SETTING THE DAY/TIME
base to hang up.
You must set the day of the week and time
so the TAD can record the correct day and
time of each message.
TURNING THE BASE’S
RINGER ON AND OFF
Note:
Enter each key press within about 2
RINGER
To turn off the base’s ringer, set
on
minutes. Otherwise, the TAD exits the time
setting process and you must begin again
with Step 1.
OFF
the back of the base to
. You can still
make or receive calls using this phone. Tele-
phones on the same line (and the TAD’s
handset if it is away from the base) still ring
when there is an incoming call.
CLOCK
1. Hold down
until the TAD beeps.
The TAD announces the currently set
day and displays the day’s number (0
for Sunday, 1 for Monday, and so on).
RINGER
To turn on the base’s ringer, set
to
ON
.
2. To change the day of the week, repeat-
SKIP
edly press
REPEAT
to move forward or
SETTING THE RINGER
TONE/VOLUME
to move backward to set the
correct day, press
CLOCK
.
You can select one of four different ringer
tone/volume settings while the phone is not
3. The TAD announces the hour. To
SKIP
change the hour, repeatedly press
VOL 8
9
in the talk mode. Press
or
to in-
REPEAT
or
until the correct hour dis-
crease or decrease the ringer level setting.
CLOCK
plays, then press
.
Note:
The setting is not cyclic. If the ringer
4. The TAD announces the minutes. To
change the minutes, repeatedly press
VOL 8
does not change when you press
or
9
, try pressing the opposite arrow key.
SKIP
REPEAT
until the correct minutes
or
CLOCK
display, then press
.
SETTING THE NUMBER OF
RINGS
5. The TAD announces “AM” or “PM,” and
SKIP
REPEAT
A or P appears. Press
or
RING TIME
3 5
Set
on the side of the base to , ,
CLOCK
to change this setting. Press
again to set “AM” or “PM.” The TAD
beeps and announces the day and time.
T/S
or
(Toll-Saver) to select how long the
TAD waits to answer a call (3 rings, 5 rings,
or toll-saver).
CLOCK
To check the day and time, press
.
Note:
distance, set
the Toll-Saver” on Page 20).
If you plan to check messages by long
The TAD announces the currently set day
and time.
RING TIME
T/S
(see “Using
to
Note:
When power fails, the clock retains the
current time. When the power is restored, the
clock starts counting again from the time the
power failed. You must reset the time.
13
Installation
43-1130.fm Page 14 Tuesday, May 30, 2000 1:22 PM
ˆ Telephone Operation
MAKING AND RECEIVING
CALLS WITH THE HANDSET
ANSWERING CALLS WITH
THE SPEAKERPHONE
To make a call, lift the handset and press
To answer a call using the speakerphone,
TALK
SPEAKER
. The SPEAKER indicator
. The TALK/LOW BATT indicator on the
press
lights.
handset and the CHARGE/IN USE indicator
on the base light. Dial the number.
To adjust the speakerphone’s volume, re-
VOLUME 8
on the
base. The volume setting from 1 (lowest) to
10 (highest) appears in the message
counter window.
9
To answer a call, lift the handset from the
base or, if the handset is away from base,
press any key to make or answer a call.
peatedly press
or
To end a call, place the handset on the base
TALK
SPEAKER
or press
.
To end a speakerphone call, press
again.
ADJUSTING THE HANDSET
VOLUME
SWITCHING BETWEEN THE
HANDSET AND
SPEAKERPHONE
To adjust the volume you hear through the
VOL 8 9#
or
handset during a call, press
to
increase or to decrease the volume.
To switch to the speakerphone while you are
SPEAKER
using the handset, press
on the
Note:
VOL 8
9
If you press
or
while the
base. When you hear the conversation on
volume is set to the maximum or lowest lev-
el, the setting does not change and you hear
three quick beeps.
TALK
the speakerphone, press
set.
on the hand-
To switch to the handset while you are using
the speakerphone, lift the handset off the
base. If the handset is away from the base,
SELECTING THE CHANNEL
The phone scans 30 channels (frequency
pairs used between the base and the hand-
set) and automatically selects a clear chan-
nel each time you make or receive a call.
TALK
SPEAKER
.
press
, then press
USING BOTH THE HANDSET
AND SPEAKERPHONE
If you hear other conversations or excessive
If someone else is using the speakerphone,
CHANNEL
noise during a call, press
a different channel.
to select
TALK
press
on the handset to join the con-
versation. If someone else is using the hand-
SPEAKER
set, press
on the base to join the
Note:
If the handset is too far from the base,
conversation.
the channel might not change. Move closer
to the base and try again.
During the call, one person can hang up and
let the call continue at the other keypad. Or,
both people can hang up to end the call.
14
Telephone Operation
43-1130.fm Page 15 Tuesday, May 30, 2000 1:22 PM
Note:
If you hear a high-pitched noise from
USING TONE SERVICES ON
A PULSE LINE
the base’s speaker, the handset and the
base are too close together. Move them
away from each other.
Some special services, such as bank-by-
phone, require tone signals. If you have
pulse service, you can still use these special
tone services by following these steps.
USING FLASH
FLASH
performs the electronic equivalent of
PULSE-TONE
PULSE
1. Be sure
is set to
.
a switchhook operation for special services,
such as Call Waiting.
2. Dial the service’s main number.
3. When the service answers, press
For example, if you have Call Waiting, press
TONE
FLASH
to answer an incoming call without
on the handset. Any additional numbers
you dial are sent as tone signals.
FLASH
disconnecting the current call. Press
again to return to the first call.
When you hang up, the phone automatically
resets to pulse dialing.
Note:
services, pressing
the current call.
If you do not have any special phone
FLASH
might disconnect
PAGING
USING REDIAL
To page the person who has the handset or
to locate the handset when the phone is not
To quickly dial the last number dialed, lift the
PAGE
in use, press
on the base. The handset
TALK
REDIAL
.
handset, press
, then press
beeps for 5 seconds. For a longer handset
PAGE
beep, hold down
for at least 5 sec-
Notes:
onds. The handset beeps for 1 minute. To
stop it from beeping sooner, press any key
• The redial memory holds up to 32 digits,
so you can redial long-distance as well
as local numbers.
TALK
on the handset except
.
Note:
The phone rings if a call comes in dur-
TALK
on the handset or
on the base to answer the call.
• The redial memory also holds pause
entries (see “Entering a Pause” on
Page 16).
ing paging. Press
SPEAKER
MEMORY DIALING
USING MUTE
You can store up to 10 phone numbers in
memory, then dial a stored number by enter-
ing its memory location number. Each stored
number can be up to 20 digits.
To talk to someone in the room without the
person on the other end of the phone line
hearing your conversation, press
MUTE
. The
TALK/LOW BATT indicator flashes.
Storing a Number in Memory
MUTE
Press
again to resume your phone
conversation.
Notes:
• The phone beeps several times and
exits the storing process if you wait
more than 20 seconds between each
key press.
15
Telephone Operation
43-1130.fm Page 16 Tuesday, May 30, 2000 1:22 PM
• If you receive a call while entering a
number in memory, the TAD exits the
storing process.
Dialing a Memory Number
To dial a number stored in memory, lift the
TALK
MEMO-
handset and press
.Then press
1. Lift the handset.
RY
and the memory location number (0–9).
MEMORY
2. Press
. The TALK/BATT LOW
Chain-Dialing Service Numbers
indicator flashes.
For quick recall of numbers for special ser-
vices (such as bank by phone), store each
group of numbers in its own memory loca-
tion.
3. Enter the phone number and any tone or
pause entries (see “Using Tone Services
on a Pulse Line” on Page 15 and “Enter-
ing a Pause”).
Dial the service’s main number first. Then, at
MEMORY
4. Press
, then select a memory
MEM-
the appropriate place in the call, press
location (0–9) by pressing the appropri-
ate number on the handset. The hand-
set sounds a tone indicating successful
storage.
ORY
and enter the number for the location
where the additional information is stored.
Testing Stored Emergency Num-
bers
For each stored number, write the contact’s
name next to the appropriate location num-
ber on the supplied memory directory sticker.
Peel the backing from the sticker and attach
it to the phone.
If you store an emergency service’s number
(police department, fire department, ambu-
lance) and you choose to test the stored
number, make the test call during the late
evening or early morning hours to avoid peak
demand periods. Also, remain on the line to
explain the reason for your call.
To replace a stored number, store a new one
in its place.
To delete a number without storing a new
MEMORY
one, press
twice. Then enter the
USING A HEADSET
memory location number you want to clear
using the handset. The handset sounds a
tone indicating the number was cleared from
memory.
You can talk with hands-free convenience
using an optional headset that has a /32 -
inch (2.5-mm) plug. Your local RadioShack
store has a variety of suitable headsets.
3
Entering a Pause
To connect the head-
set, open the rubber
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before you can dial an out-
side number. You can store the access code
with the phone number. However, you
should also store a pause after the access
code to allow the outside line time to con-
nect. To enter a 2-second pause, press
cover with
marked
on the side of the hand-
set, then insert the
headset’s plug into the
jack.
When you finish using the headset, discon-
nect it from the handset and close the rubber
cover to protect the jack.
PAUSE
. You can add more pause entries for
a longer pause.
16
Telephone Operation
43-1130.fm Page 17 Tuesday, May 30, 2000 1:22 PM
Notes:
• With a headset connected, you can
make or answer calls as usual using the
keys on the handset. You can also
• Connecting a headset disconnects the
handset’s earpiece and microphone.
SPEAKER
answer calls by pressing
located on the base.
VOL 8
9
MUTE
or on the handset
•
or
also controls the connected headset’s
volume.
• You can use a handset holder (available
from your local RadioShack store) to
hang the handset on your belt for
greater convenience.
• If you place the handset on the base to
recharge it while the headset is con-
nected, be sure the handset seats prop-
erly.
ˆ TAD Operation
SELECTING THE OUTGOING
MESSAGE
RECORDING/DELETING AN
OUTGOING MESSAGE
The TAD has two prerecorded outgoing mes-
sages. One asks the caller to leave a mes-
sage: “Hello, no one is available to take your
call. Please leave a message after the tone.”
To record your outgoing message (up to 30
OGM
seconds long), hold down
until the TAD
beeps and -- appears. When you finish
PLAY/STOP
OGM
.
your message, press
or
REC TIME
The TAD uses this message when
The TAD plays back your message.
1
4
is set to
Time”).
or
(see “Setting the Record
To delete your outgoing message and use
the TAD’s prerecorded messages, hold
OGM
The other recording is an announcement and
does not let the caller leave a message: “Hel-
lo, no one is available to take your call.” The
down
OGM
until the TAD beeps. Then press
again within two seconds.
REC TIME
TAD uses this message when
is
SETTING THE RECORD
TIME
ANN
set to
(announcement only).
You can also record your own message (see
“Recording/Deleting an Outgoing Message”).
When you record your own outgoing mes-
REC TIME
1
4
ANN
to determine
Set
to
,
, or
how the TAD will record incoming messages.
REC TIME
sage, the TAD uses it for all
tings.
set-
1
— The TAD plays the outgoing mes-
sage and lets callers leave a message
up to 1 minute long.
To switch between your outgoing message
and the TAD’s prerecorded message, press
. When the current message begins to
again. The TAD switches to
the other message and plays it.
4
— The TAD plays the outgoing mes-
OGM
sage and lets callers leave a message
up to 4 minutes long.
OGM
play, press
17
TAD Operation
43-1130.fm Page 18 Tuesday, May 30, 2000 1:22 PM
ANN
(announcement only) — The TAD
• The caller hangs up.
plays the outgoing message but does
not let callers leave a message.
• The maximum message length is
reached.
SETTING THE TAD TO
ANSWER CALLS
• The TAD detects a busy signal or more
than 7 seconds of silence.
AN-
To set the TAD to answer calls, press
SWER
• You pick up the TAD’s handset or any
phone on the same phone line.
on the base. If the TAD is set to record
a caller’s message (see “Setting the Record
Time” on Page 17), it plays the outgoing
message and shows the number of recorded
messages. If the TAD is set to announce-
ment-only, it plays the outgoing message,
and A appears.
Note:
When the TAD’s message memory is
full, FL appears on the display and the TAD
announces “No remaining time” when you try
to operate it.
RECORDING A MEMO
To set the TAD to not answer calls, press
ANSWER
. The TAD announces “Answer off”
A memo is a message you can record at the
TAD for yourself or others in your home or
office. The TAD stores memos as incoming
messages (see “Playing Messages” on
Page 19).
and the message counter disappears.
SCREENING CALLS
You can let the TAD answer calls while you
listen to the caller’s message through the
base’s speaker. If you decide to answer the
MEMO
To record a memo, hold down
on the
base until the TAD beeps and –– appears in
the message counter window, then speak
your message. When you finish the memo,
SPEAKER
call, press
speakerphone, press
to answer using the
TALK
to answer if the
PLAY/STOP
MEMO
.
handset is off the base, or lift the handset if it
is on the base. You can also pick up any
phone on the same line. The TAD stops re-
cording and resets to answer the next call.
press
or
Note:
The TAD cannot record a memo less
than two seconds long.
RECORDING A
CONVERSATION
RECORDING INCOMING
MESSAGES
The TAD lets you record both sides of a tele-
phone conversation when you are talking
with the handset.
After the TAD answers a call, it plays the out-
going message, beeps, and records the call-
er’s message.
Important:
Every state has different regula-
Each incoming message can be up to 1 or 4
minutes long, depending on how you set
tions governing the recording of conversa-
tions over the telephone. Be sure to check
your local, state and federal laws before us-
ing this product to record any telephone con-
versation in order to determine that your use
is in compliance with such laws or guide-
lines.
REC TIME
(see “Setting the Record Time” on
Page 17). The TAD’s maximum recording
capacity is 18 minutes.
The TAD stops recording and resets to an-
swer the next call when:
18
TAD Operation
43-1130.fm Page 19 Tuesday, May 30, 2000 1:22 PM
To start recording a phone conversation,
DELETING MESSAGES
MEMO
hold down
on the base until the TAD
To delete the current message while it is
beeps and –– appears. To stop recording,
DELETE
playing, hold down
beeps.
until the TAD
PLAY/STOP
MEMO
.
press
or
The TAD stores a recorded conversation as
a message (see “Playing Messages”).
To delete all messages at once, while mes-
DELETE
sages are not playing, hold down
on
Note:
The TAD does not record conversa-
the base until the TAD beeps and 0 appears
in the message counter window.
tions less than two seconds long, or that use
the speakerphone.
Note:
You cannot delete new (unplayed)
messages. If you try to delete all messages
at once while you still have new messages,
the TAD beeps quickly five times and does
not delete any messages.
PLAYING MESSAGES
After the TAD has recorded a message, the
total number of messages stored appears in
the message counter window. If you have
new messages, the message counter flash-
es.
SETTING THE REMOTE
OPERATION PIN
PLAY/STOP
To play your messages, press
.
The TAD’s two-digit remote operation PIN
(personal identification number) prevents un-
authorized remote access to your messages.
The PIN is preset to 80. Follow these steps
to change the PIN to any number from 00 to
99.
The TAD announces the number of new and
old messages, then plays the new messag-
es. The message number appears in the
message counter window as each message
plays, and the TAD announces the day and
time of the call at the end of each message.
Note:
If you wait more than 2 minutes be-
To play all messages after playing the new
tween each keypress, the TAD exits the PIN
setting process. Start again at Step 1.
PLAY/STOP
messages, press
again.
SKIP
To skip to the next message, press
ing playback.
dur-
PIN
1. Hold down
until the TAD beeps and
00 appears in the message counter win-
dow.
To replay the current message from the be-
REPEAT
REPEAT
ginning, press
. If you press
SKIP
2. Press
to set the first digit of the PIN
within about 2 seconds after a message be-
gins playing, the TAD replays the previous
message.
REPEAT
higher or
to set it lower. Then
PIN
press
.
SKIP
REPEAT
to set the second
3. Press
or
PIN
digit of the PIN, then press
announces the new PIN.
. The TAD
ADJUSTING THE TAD’S
VOLUME
PIN
To check your PIN at any time, press
.
To adjust the speaker’s volume, repeatedly
The PIN appears in the message counter
window, and the TAD announces it.
VOLUME 8
9
press
or
on the base. The
volume setting from 1 (lowest) to 10 (high-
est) appears in the message counter win-
dow.
19
TAD Operation
43-1130.fm Page 20 Tuesday, May 30, 2000 1:22 PM
Note:
SPEAKER
PLAY/STOP
or
If you press
1. Dial your phone number and wait for the
TAD to answer.
while changing the PIN, the TAD exits. Begin
again with Step 1.
2. If the TAD is not set to answer calls, it
will answer after about 10 rings and
sound a series of beeps.
REMOTE OPERATION
While you are away from your home or of-
fice, you can use a touch-tone phone, or a
pulse (rotary) phone with a pocket tone dialer
(not supplied and available through your lo-
cal RadioShack store) to enter your PIN and
do any of the following:
3. When the outgoing message begins (or
the TAD sounds a series of beeps),
#
press , then enter your PIN within 2
seconds.
If the PIN is correct, the TAD announces the
day and time, then it announces the number
of new and old messages. The TAD plays all
new messages then beeps about once every
two seconds to let you know it is ready to ac-
cept remote commands.
• Set the TAD to answer or not answer
calls.
• Listen to your messages.
• Record a new outgoing message.
• Record a memo.
Notes:
• If the TAD does not respond, try entering
your pin again. If you enter an incorrect
PIN three times, the TAD beeps and
hangs up.
• Erase messages.
Note:
You cannot remotely operate the TAD
using its handset or another telephone on
the same line as the TAD.
• When the TAD is in remote operation, it
stops all answering functions and rC
appears on the base’s display. The TAD
resumes answering functions when it is
no longer in the remote command if you
did not turn it off.
USING THE TOLL-SAVER
RING TIME
T/S
(toll-saver), (see
If
is set to
“Setting the Number of Rings” on Page 13),
the TAD answers after three rings if you have
new messages (ones you have not listened
to). If there are no new messages, the TAD
answers after five rings. This gives you time
to hang up before the TAD answers so you
can avoid unnecessary long-distance charg-
es.
• The remote playback of incoming mes-
sages is limited to 4 minutes. If you have
more messages after 4 minutes have
# 2
passed, you must press
again to lis-
ten to the rest of the messages.
• When using remote operation, you can
only delete the current message during
playback. You cannot delete all the mes-
sages stored at one time.
USING REMOTE
COMMANDS
Follow these steps to operate the TAD from
a remote location.
• The maximum length of
recorded by remote operation is 4 min-
utes.
a
memo
Note:
If you wait more than 15 seconds be-
tween each keypress, the TAD sounds a
long beep and hangs up.
20
TAD Operation
43-1130.fm Page 21 Tuesday, May 30, 2000 1:22 PM
#
To enter a remote command, press and
(within 2 seconds) the number for the com-
mand you want.
Note:
The remote operation stops when
someone picks up the handset or any phone
on the same phone line.
Remote Commands
Press #
To
then
1
Repeat the current message during
playback.
2
3
Play messages.
Skip the current message during play-
back.
4
5
Delete the current message during
playback.
Stop playback, recording, or room
monitoring.
6
7
8
Set the TAD to answer calls.
Record or stop recording a memo.
Record or stop recording a new out-
going message.
9
Set the TAD to not answer calls.
Monitor the room where the TAD is
located.
21
TAD Operation
43-1130.fm Page 22 Tuesday, May 30, 2000 1:22 PM
ˆ Troubleshooting
We do not expect you to have any problems with your TAD, but if you do, these suggestions
might help.
Problem
Suggestion
Low volume or unusual sounds.
Someone has picked up another phone on the same line. Hang
up the other phone.
CHANNEL
to change the channel.
Severe noise interference.
Press
Keep the handset away from computers, remote control toys,
wireless microphones, alarm systems, intercoms, room monitors,
fluorescent lights, and electrical appliances.
Move the handset to another location or turn off the source of
interference.
The phone cannot be operated at a Lift the base’s antenna to a vertical position.
useful distance from the base
because the signal becomes weak
Be sure neither antenna is touching a metal surface.
Return the handset to the cradle, and recharge the battery pack.
Replace the battery pack if necessary (see “Connecting, Charg-
ing, and Replacing the Battery Pack” on Page 10).
or noisy (handset’s range has
decreased).
The phone does not work or works Be sure the base’s phone line cord and AC adapter are correctly
poorly. and securely connected, and the battery pack is charged.
The handset battery pack does not Check the charging contacts on the handset and base. If they are
charge.
dirty, clean them with a pencil eraser.
Be sure the battery pack is connected correctly.
Replace the battery pack.
The handset does not ring or
receive a page.
Move the handset closer to the base.
Lift the base’s antenna to a vertical position.
Be sure the battery pack is charged. (If the battery power is too
low, it does not have enough power to light the TALK/LOW BATT
indicator.)
Move the base away from other electrical devices and sources of
noise.
The handset stops working or
works poorly during a call.
Move the handset closer to the base.
Lift the base’s antenna to a vertical position.
Be sure the battery pack is charged. (If the battery power is too
low, it does not have enough power to light the TALK/LOW BATT
indicator.)
22
Troubleshooting
43-1130.fm Page 23 Tuesday, May 30, 2000 1:22 PM
Problem
Suggestion
The handset stops working or
works poorly during a call (contin-
ued).
If the base loses power while the handset is away, the security
access-protection code might change. Restore power to the base,
then place the handset back on the base. The CHARGE/IN USE
indicator lights, indicating that the code is set again.
Check the charging contacts on the handset and base. If they are
dirty, clean them with a pencil eraser.
The TAD does not answer calls.
Make sure the TAD is turned on.
Make sure the AC adapter is properly connected.
Check all phone line connections.
REC TIME
ANN
1
4
.
The TAD does not record callers’
messages.
is set to
(announcement only). Set it to or
Delete messages if memory is full.
If you still have problems, disconnect the TAD. If other phones on the same line work properly,
the fault is in this phone or its installation. If you cannot find the problem, take your phone to
your local RadioShack store for assistance.
CARE
To enjoy your phone for a long time:
• Keep the phone dry. If it gets wet, wipe it
dry immediately.
• Use and store the phone only in normal
temperature environments.
• Handle the phone gently and carefully.
Do not drop it.
• Keep the phone away from dust and dirt.
• Wipe the phone with a damp cloth occa-
sionally to keep it looking new.
Modifying or tampering with the phone’s in-
ternal components can cause a malfunction
and might invalidate its warranty and void
your FCC authorization to operate it. If your
phone is not performing as it should, take it
to your local RadioShack store for assis-
tance. If the trouble is affecting the telephone
lines, the phone company can ask you to dis-
connect your phone until you have resolved
the problem.
23
Troubleshooting
43-1130.fm Page 24 Tuesday, May 30, 2000 1:22 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
43-1130
UCZZ01691BZ
05A00
Printed in China
RadioShack Corporation
Fort Worth, Texas 76102
|